Winkler One Flooring

Coverage Calculator
Get an estimate
Area Sqm:
Height(M):
Width(M):
Reset fields
Calculate
A wastage allowance of 10% is built-in for your convenience.
£468.58 £390.48

Winkler One Flooring is a single component pigmented water-proofing liquid that is applied to high traffic horizontal surfaces.

It is UV resistant and is suitable for interior or exterior use. Winkler One Flooring can even be applied in extreme conditions at temperatures ranging from 0°C to +45°C and over damp or wet substrates.

 

 

 

Winkler One Flooring

Price: £468.58
Inc. VAT
Price: £390.48
Excl. VAT
Enter a new project name
Quantity
?
SKU: VVONFG20

YouTube Terms & Conditions.

At a Glance

  • Liquid waterproofing membrane for high traffic horizontal surfaces.
  • Suitable for surfaces with vehicular stress.
  • For interior and exterior use.
  • Can be applied in cold or damp conditions.
  • Colour: Grey
  • Size: 20kg.

Usage 

One Flooring is particularly recommended for waterproofing and protecting floors/decks subjected to high levels of stress such as:

  • Garages or car parking facilities.
  • Storage or warehouse facilities.
  • Industrial floorings and substrates such as concrete, ceramic tiles, or other floors/decks with permanent problems of excess dampness.
  • Cement-based screeds that are not fully cured (7 days at 15°C).
  • Tarmac (with minimum mechanical resistance of 0.5 N/mm2).

Surface Preparation

Clean all substrate surfaces thoroughly to eliminate dirt, dust, and loose materials, any form of oil or grease and foreign or bonding-proof matter.

The substrate shall be sound and cohesive with a tear resistance value of at least 1.5 MPa. If oil stains are present on concrete proceed as follow:

  • Mechanically remove approximately 2 mm of the substrate surface where oil is present, remove all dust (with vacuum aspirator).
  • Immediately apply Winkler One Primer (two-component epoxy adhesion promoter) with a roller or flat brush and broadcast quartz 01-05 onto the wet primed surface. Allow One® Primer to cure for at least 24 hours.

When repairing any surface up to a maximum of 2m², apply Winkler Pre-One (fast-setting thixotropic mortar), using a trowel or smooth putty knife. Apply and cure Pre-One® at temperatures between 0°C and +45°C. Follow instructions contained in the Technical Specification Sheet for more detail.

If the area is larger than 1m² (max. 2m²) and/or has more than 1cm in depth we strongly recommend applying Pre-One in 2 coats, allowing each coat to cure properly (min. 12 hours) prior to the application of any subsequent layer of material. Any cracks that may appear in the product after the first coat is cured, can be repaired with the second coat. Allow the second coat to cure for at least 12 hours.

When repairing any surface larger than 2m² follow the steps below, observing the application and curing temperature range between + 5°C to + 30°C:

  • Up to 3 mm thickness: apply Unibat Formula* (multifunctional two-component resin) with a roller or flat brush, following the instructions in the latest product Technical Specification Sheet. Allow the product to set for several minutes, up to a maximum of 24 hours, before continuing to restore the surface with Unibar SL* (self-levelling tri-composite for screeds (SC2)). Wait at least 24 hours before applying Winkler One® Flooring.
  • Over 3 mm thickness: apply Unibar Formula* (multifunctional two-component resin) with a roller or flat brush, following instructions in the latest product Technical Specification Sheet. Allow the product to set for several minutes, up to a maximum of 24 hours, before continuing to restore the surface with Unibar Malta* (synthetic tri-composite mortar (SC1)). Wait at least 24 hours before applying Winkler One® Flooring.
If oil stains are present on tarmac surfaces proceed as follow:
  • Mechanically remove at least 4-5 cm of the contaminated tarmac surface
  • Remove all dust (with vacuum aspirator).
  • Restore holes with Technoasfalt* (cold tarmac conglomerate made from modified bitumen).
  • After proper compacting, proceed with the application of One Flooring.

Application

Stir the product thoroughly before use.

One Flooring is ready for use and does not need a primer or protective topcoat.

Apply with a short-haired roller, smooth trowel, or airless spray gun (Larius – Thor series). 

Apply the first coat by short-haired roller for a consumption of 350-400g/m².

Wait for the time indicated on the temperature table (see specification sheet), then apply the second coat, always with a roller or metal trowel, for a rate of 1.1-1.2 kg/m².

The use of a spiked roller after the second coat, before it cures, is always recommended.

For best results, apply a finishing coat of the product with a short-haired roller in longitudinal and transversal strokes, for a consumption of 300g/m². 

In all cases, please allow each coat to cure according to the guide shown in the Technical Specification Sheet. 

For applications on surfaces subject to movements, such as tiled foundations, apply the product as described below:

  • After carefully cleaning the surface to be treated, regularize the volume of the joints with Winkler One Vertical (300g/m²), using a smooth trowel.
  • After at least 8 hours, apply One Flooring (with a consumption of 400g/m²), evenly.
  • Immediately lay Winkler One Mat, non-woven 90g/m² reinforcement, by using a spiked roller and soak it with other 500-600g/m² of One Flooring.
  • Wait for the time required for the application of the second coat (see temperature table for application with reinforcement), and apply 600-700g/m² of product.
  • We always recommend the use of a spiked roller after the application of the second coat.
  • Wait for the time indicated in the temperature table and apply the finishing coat with a short-haired roller, with a consumption of 300g/m² in a longitudinal and transverse direction.

Full mechanical resistance is achieved 7 days after applying the last coat.

Consumption

1.7 - 1.9 kg/m² without reinforcement.
1.8 - 1.9 kg/m² with One Mat.

Storage

The product can be stored in a dry and sheltered place at temperatures between +5°C and +35°C for 12 months in its unopened and undamaged packaging.

 

* Unibar products and Technoasfalt are special order items, please contact us to order these products.

Courier Delivery

Max 2 items

Leadtime:
Up to 3 working days.

Cost:
Starting from £15.00.

Palletised Delivery

For 3 or more items

Leadtime:
5-7 working days.

Cost:
Starting from £46.00 per pallet.

You can view our detailed delivery charges and services here.